Description
Purchase Carver® 7INF11BA Styled-To-Fit® Trailerable Boat Cover part number [7INF11BA] guaranteed to fit Zodiac® Cadet 350 ALU (2018-2024) Boat-Cover-CSF-Model™Carver(r) 7INFxxB series Styled-To Fit(tm) boat cover (for Blunt Nose Inflatable boat; O/B) provides a GUARANTEED Fit Boat Cover CSF Model 7INFxxB, Boat Sketch. Boat-Cover-CSF-Model™Carver(r) 7INFxxB series Styled-To Fit(tm) boat cover (for Blunt Nose Inflatable boat; O/B) provides a GUARANTEED Fit Boat Cover CSF Model 7INFxxB, Blunt Nose RIB Photo. Notes: Carver® has made boat covers in South Carolina, USA for 40+ years: This cover was patterned for this specific STYLE, length, width and setup of boat, so it is GUARANTEED TO FIT or we will replace it or have it returned for a refund (https://dealerguide.carvercovers.com/mmy/boat).Be sure this is your exact year, make and model boat, because this cover is subject to a 35% restocking fee, 1/4" Stretch Cord in hem (NO Snaps or Clips) pulls cover tightly under your rub rail, TRAILERABLE at reasonable highway speeds when cinched tightly with (12) FREE Heavy Duty TIE-DOWN STRAPS (6 on smaller covers) connected to the Sturdy TIE-DOWN-LOOPS (every 2 feet, double sewn in an offset "V" for strength), Can also be used on drive-on FLOAT, DRY-STACK, SEA-PEN or IN-WATER (Not on a LIFT) with optional Sand Bags (below), but there are NO openings for lines to your cleats, Offered in three solution dyed fabrics (rather than just dyed on the surface, to reduce fading), DOUBLE-STITCHED using weather resistant anti-wick thread and FOLDED FOUR-PLY JOIN SEAMS (no raw edges) for added strength and durability, MOTOR COVER sewn into outboard model boat covers (some have separate motor cover). Size/Fit: NO RISK! GUARANTEED TO FIT the 2018-2024 Zodiac® Cadet 350 ALU: Blunt Nose Inflatable boat; O/B, No Bimini; No Tower or Arch. Bimini-Tops must be lowered and stored flat or removed (unless stated otherwise), Does NOT have or use Snaps or Clips like a factory original Bow, Cockpit or Playpen Cover, Pedestal Seats must be removed or lowered, "Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION ABOVE: • Other boat models or years (it MAY fit other boats, but NO guarantee of fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.," Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location, NOT intended for use on a LIFT, as it is difficult to pull the cover back over the transom properly. Guarantee: RnR-Marine™ and Carver® Industries, Inc. (the manufacturer) guarantee the quality of workmanship and materials, and will resolve quality issues found upon delivery by repairing or replacing (at their discretion) the item in question. Carver® also guarantees that Custom-fit® and Styled-To-Fit® Boat Covers will fit the specified year, make, mode and configuration or we will resolve the issue (https://dealerguide.carvercovers.com/mmy/boat). Warranty: The materials and workmanship are guaranteed by Carver® to be free of defects at time of manufacture and are covered by Carver's® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®/Outdura®: 10 years, Sun-Dura™: 7 years. (Note: The use of Bungee Cords instead of Tie-Down Straps on Boat-Covers will void the warranty). (All product warranties are listed on https://RnR-Marine.com/Warranty.shtml#Warranties).
